Güzel, A.; Jäger, A.; Parvizian, F.; Lambers, H.-G.; Tekkaya, A.E.; Svendsen, B.; Maier, H.J.
“A New Method for Determining Dynamic Grain Structure Evolution During Hot Aluminum Extrusion”.
J. Mater. Process. Techn., 212, pp. 323-330, 2012

Rubitschek, F.; Niendorf, T.; Karaman, I.; Maier, H.J.
“Corrosion Fatigue Behavior of a Biocompatible Ultrafine-grained Niobium Alloy in Simulated Body Fluid”.
J. Mech. Behavior of Biomed. Mater., 5, pp. 181-192, 2012

Sangid, M.D.; Pataky, G.J.; Sehitoglu, H.; Hamilton, R.F.; Maier, H.J.
“High Resolution Analysis of Opening and Sliding in Fatigue Crack Growth”.
Int. J. Fatigue, 37, pp. 134-145, 2012

Rüsing, C.J. Niendorf, T. Lackmann, J. Frehn, A. Maier, H.J.
“Microstructure-Deformation Relationships in Fine Grained High Manganese TWIP Steel - The Role of Local Texture”.
Int. J. Mater. Res., 103, pp. 12-16. 2012

Rubitschek, F.; Niendorf, T.; Karaman, I.; Maier, H.J. 
„Microstructural Stability of Ultrafine-grained Niobium-zirconium Alloy at Elevated Temperatures”.
J. Alloys and Compounds, 517, pp. 61-68, 2012

Böhner, A.; Niendorf, T.; Amberger, D.; Höppel, H.W.; Göken, M.; Maier, H.J.
“Martensitic Transformation in Ultra.ne-grained Stainless Steel AISI 304L Under Monotonic and Cyclic Loading”.
Metals, 2, pp. 56-64, 2012

Holzweissig, M.J.; Canadinc, D.; Maier, H.J.
“In-situ Characterization of Transformation Plasticity During an Isothermal Austenite-to-Bainite Phase Transformation”.
Mater. Characterization, 65, pp. 100-108, 2012

Toker, S.M.; Rubitschek, F.; Niendorf, T.; Canadinc, D.; Maier, H.J.
“Anisotropy of Ultrafine-grained Alloys Under Impact Loading - The Case of Biomedical Niobium-Zirconium”.
Scripta Mater., 66, pp. 435-438, 2012

Lambers, H.-G.; Rüsing, C.J.; Niendorf, T.; Geissler, D.; Freudenberger, J.; Maier, H.J.
“On the Low-cycle Fatigue Response of Pre-strained Austenitic Fe₆₁Mn₂₄Ni₆:5Cr8:5 Alloy Showing TWIP Effect”.
Int. J. Fatigue, 40, 51-60, 2012

Lambers, H.-G.; Canadinc, D.; Maier, H.J.
”Evolution of Transformation Plasticity in Austenite-to-Bainite Phase Transformation: A Multi Parameter Problem“.
Mater. Sci. Eng. A, 541, pp. 73.80, 2012

Zhu, R.; Li, S.; Karaman, I.; Arroyave, R.; Niendorf, T.; Maier; H.J.
“Multi-phase Microstructure Design of a Low-alloy TRIP-assisted Steel Through a Combined Computational and Experimental Methodology”.
Acta Mater., 60, pp. 3022-3033, 2012

Purcek, G.; Saray, O.; Karaman, I.; Maier, H.J.
“High Strength and High Ductility of Ultrafine-Grained, Interstitial-Free Steel Produced by ECAE and Annealing”.
Metall. Mater. Trans. A, 43A, pp. 1884-1894, 2012

Holzweissig, M.J.; Canadinc, D.; Maier, H.J.
“In-situ Characterization of Backstress Effects on the Austenite-to-Bainite Phase Transformation”.
Scripta Mater., 67, pp. 368-371, 2012

Ezaz, T.; Sehitoglu, H.; Abuzaid, W.; Maier, H.J.
”Higher Order Twin Modes in Martensitic NiTi - The (201) Case”.
Mater. Sci. Eng. A, 558, 2012, pp. 422.430.

Pataky, G.J.; Sangid, M.D.; Sehitoglu, H.; Hamilton, R.F.; Maier, H.J.; Sofronis, P.
“Full Field Measurements of Anisotropic Stress Intensity Factor Ranges in Fatigue”.
Eng. Fracture Mech., 94, pp. 13-28, 2012

Saray, O.; Purcek, G.; Karaman, I.; Maier, H.J.
“Impact Toughness of Ultra-.ne Grained Interstitial-free Steels”.
Metall. Mater. Trans. A, 43A, pp. 4320-4330, 2012

Niendorf, T.; Rüsing, C.J.; Frehn, A.; Chumlyakov, Y.I.; Maier, H.J.
“Deformation Mechanisms in High-Manganese Steels Showing Twinning-induced Plasticity: Fine-grained Material and Single Crystals at Ambient and Cryogenic Temperatures”.
Scripta Mater., 67, pp. 875-878, 2012

Sehitoglu, H.; Wang, J.; Maier, H.J.
„Transformation and Slip Behavior of Ni2FeGa”.
Int. J. Plasticity, 39, pp. 61-74, 2012

Niendorf, T. Klimala, P. Maier, H.J. Frehn A.
"The Role of Notches on Fatigue Life of TWIP Steel in the HCF Regime"
Proc. Thermec 2011, Mater. Sci. Forum, 706-709, 2012, pp. 2205-2210.

Schmidt, H.C.; Damerow, U.; Lauter, C.; Gorny, B.; Hankeln, F.; Homberg, W.; Troester, T.; Maier, H.J.; Mahnken, R.:
”Manufacturing Processes for Combined Forming of Multi-material Structures Consisting of Sheet Metal and Local CFRP Reinforcements”.
Key Eng. Mater., 504-506, pp. 295-300, 2012

Brenne, F.; Niendorf, T.; Maier, H.J.
“Optimization of Lattice Structures manufactured by Selective Laser Melting”.
Proc. 1st Int. Conf. of the Int. J. of Structural Integrity, Porto, pp. 40-50. 2012